Any project, any size.

If Spray Foam Insulation is installed in the vicinity of heat emitting devices or ignition sources, it requires a minimum 15-minute Thermal Barrier, as per building code regulations. This can be obtained with one ½” sheet of drywall where design and accessibility allows, or by a variety of spray-applied Thermal Barrier products.
We at Ultimate Foam and Fire are trained to install a variety of spray-applied Thermal Barrier products, and with our product selection, you will be able to choose the Ultimate solution to fit your projects unique needs:

AD FIRE - Type 7TB
This cementitious Thermal Barrier is the budget friendly option in situations where finish is not of great concern. Generally chosen to be utilized in areas that will not be visible to the general public post-completion of the project. Areas could include: above suspended ceiling, in mechanical rooms, or in crawlspaces or attics. Formulated with vermiculite and Portland cement, it is an excellent choice for high humidity areas as it resists moisture well. It has high durability to physical damage which can be beneficial in high-traffic areas, such as loading docks, storage areas, or maintenance shops. It is non-combustible, asbestos, mineral wool, and styrene -free. It is non-corrosive and can be installed near and in-contact with bare steel, which may also provide heat protection of structural steel in the event of a fire. 
There are few on-site considerations as it does not require the isolation of application areas. 
Substrate (Spray foam) must be dry at time of application.
A minimum 10 degrees Celsius for the duration of application and cure.
Cure-time depends on ambient conditions.
Cures to a rough dark grey/brown finish.

Flame Seal TB-C
An attractive intumescent Thermal Barrier-Coating, optimal for areas which will be exposed to the general public once the project is complete. Intumescent coatings create a protective layer of Carbon Foam when exposed to a fire or extreme heat, thus blocking the fire and preventing heat from transferring to the Spray Foam Insulation beneath. Once cured this product is impact resistant, and does not require a top coat for protection.
This product must not be covered or painted over, as this would affect its protective and reaction properties.
Some site considerations include: the isolation of the spray areas during the application process and initial cure window (while wet to touch) and a longer application process as two coats are required to reach minimum thickness. 
Substrate (Spray foam) must be dry at time of application.
Minimum substrate and ambient temperature of 15 degrees Celsius throughout application and cure time.
Cure time of 24hrs.
The standard option cures to a bright white semi-gloss finish; is available in 5 colors.

IFTI - DC315
DC315 is an intumescent coating similar in function to Flame Seal TB-C. However, it can be applied in one coat, therefore reducing total application time. 
Similar site considerations to Flame Seal-TB where the spray areas must be isolated during the application process and initial cure window (while wet to touch). 
Substrate (Spray foam) must be dry at time of application.
Minimum substrate and ambient temperature of 15 degrees Celsius throughout application and cure time.
Cure time of 24hrs.
This product comes in light grey and can be coated with its approved top coat for color finish, weather, and moisture protection.   
* This product is currently only available to be installed with an independently approved architect/engineer design.

                                                   

In addition to Spray Foam Insulation and spray-applied Thermal Barriers, Ultimate Foam and Fire also offers two options for spray-applied Fire Proofing systems. Fire Proofing systems provide the 1-hour, 2-hour, and 3-hour egress requirements by law to ensure your buildings occupants can escape to safety in the event of a fire. Confidently meet the Fire Code Regulations required for your project, by protecting your buildings structural steel with either our cementitious or intumescent Fire Proofing products. 

AD FIRE - Type 5GP & MD
Our cementitious product can be applied to thicknesses that meet required ratings up to 4 hours, one hour beyond the minimum requirements of industry standards. Qualified for use in over 100 ULC designs intended for the fire protection of interior structural columns, beams, joists, decks, walls, roofs, girders, floors, and pre-cast concrete units. This product is durable, non-combustible, asbestos, mineral wool, and styrene -free, as well as an economical option to keep your project on budget.
There are few on-site considerations as it does not require the isolation of application areas. 
Substrate must be dry at time of application.
A minimum 10 degrees Celsius for the duration of application and cure.
Cure-time depends on ambient conditions. Can be combined with approved accelerator for a faster cure.
Cures to a rough medium grey/brown finish.

AD FIRE – Fire Film 3 & 4
This product is an attractive thin Fire Proofing coating, ideal for structural steel members in areas which will remain exposed to the general public. This product is the Ultimate solution in areas where space, accessibility, or finish is of concern. Fire ratings through traditional means, such as gypsum board or cementitious fire-proofing, can add bulk and waste valuable space, a thin intumescent coating will provide the fire rating needs, while maintaining maximum useable space. Recommended for the protection of interior steel beams, columns, tubes, and pipes. 
Depending on the rating required, several application coats may be required. Each with a minimum 24-hour cure period between coats.
Spray areas must be isolated during the application process, during each coat, and the duration of cure.
Substrate (Spray foam) must be dry at time of application.
Minimum substrate and ambient temperature of 15 degrees Celsius throughout application and cure time.
Decorative satin finish, off-white in color, ‘orange peel’ texture. Compatible top coats are available in a variety of colors, and are required in high-humidity areas.

                                                   

Lastly, Ultimate Foam and Fire is the top installer and product supplier for Hilti Firestop Systems in Western Canada. By utilizing a variety of Hilti Firestop products and systems in conjunction with approved Engineer/CCMC/ULC designs, we can confidently meet Fire Code Regulations and address all of your Fire and Smoke Stopping needs.

HILTI – FireStop Systems
Depending on your projects needs, we offer a wide selection of hand, trowel, or spray-applied Fire Rated Caulking and Smoke Sealants. This includes: tubes, paints, pipe collars & wraps, blocks & plugs, putties, foam, and coatings.

                                                   

At Ultimate Foam and Fire, we pride ourselves on the installation of our products with years of experience, continuous education, and proper use of safety equipment; for both ourselves and protecting those around us, including other workers, the public, and the environment. Our staff members are competent and reliable, certified in all of our product, safety, and equipment needs. 
Regardless of the size or complexity of your next project, you can be certain it will be completed to industry standards by experienced installers.